![]() |
![]() |
Introduction
WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power.
Where WM101 goes
Injection-molded parts that need a black surface
Crates, bins, buckets, pipe fittings, caps, plant pots, cable reels, machine covers, internal structural parts.
On walls of 3 mm and up a working black arrives at a low carbon black level, which is what an 18% grade is for.
The published floor is 0.8%, and on a thin section that reads as charcoal. Most molders settle between 1.5% and 3.0%, and stop once the part matches the reference sample.
Flow matters as much as loading here. At 10–20 g/10 min the melt fills a long, narrow flow path before the front stalls,
so thin-wall and multi-cavity tools run at a lower injection pressure than they would on a stiffer black grade.
Commodity blown film bags
The grade runs at 4.0–8.0% on market bags, T-shirt bags, produce bags, refuse sacks, bin liners and general packaging film. What you get depends on the gauge.
At 4% in a 20 micron bag the film carries about 0.7% carbon black, a soft charcoal where the resin still shows through.
A sack that has to be fully opaque usually wants 1.5–2.0% in the film, which pushes this grade to 8–11%.
You can go there, but past 8% a higher-loaded grade is normally the cheaper route to the same film, so it is worth checking the comparison below first.
Carbon black is also the UV screen in black film. Sheeting that spends its service life in the sun, mulch film, construction covers, waste bags stored outdoors, wants 2% and up in the film.
WM101 reaches that only at the very top of its range. Tell us the end use and we will point you at the outdoor grades instead.
Sheet, profile and conduit
Extrusion runs at 1.0–5.0%. Flat sheet, conduit, corrugated profile and cable duct sit near the top of that band when the surface is visible, and lower when the wall is thick and hidden.
For buried non-pressure drainage and sewer pipe, the general low carbon grade carries a worked cost comparison you can reuse.
WM101 or WM30, which one fits
Both grades run on a PE carrier at the general-purpose end of the range, so buyers often ask which to stock. The two are close enough that the numbers side by side do most of the work.
|
Item |
WM101 |
WM30 |
|
Carbon black content |
18% ± 2 |
32% ± 1.5 |
|
Carrier |
PE |
PE |
|
MFI, 190 °C / 10 kg |
10–20 g/10 min |
1–10 g/10 min |
|
Moisture |
≤ 0.3% |
≤ 0.3% |
|
Dispersion |
≤ Level 3.0 |
≤ Level 2.5 |
|
Compliance |
RoHS |
RoHS |
|
Injection dosage |
0.8–3.0% |
0.8–2.0% |
|
Blown film dosage |
4.0–8.0% |
4.0–8.0% |
|
Extrusion dosage |
1.0–5.0% |
1.0–4.0% |
|
Resins named on the TDS |
PE, PP |
PE, PP, ABS |
More carbon black per bag means less masterbatch per tonne. What each grade needs to reach the same finished color.
|
Carbon black target in the finished part |
WM101 dosage |
WM101 per tonne of resin |
WM30 dosage |
WM30 per tonne of resin |
|
0.5% |
2.8% |
28 kg |
1.6% |
16 kg |
|
1.0% |
5.6% |
56 kg |
3.1% |
31 kg |
|
2.0% |
11.1% |
111 kg |
6.3% |
63 kg |
At a 1.0% target, WM30 gets you there on 31 kg per tonne while WM101 needs 56 kg. Multiply that gap by your annual tonnage and the decision stops being about the price printed on the bag.
Take WM101 when flow and price per kilogram matter more than kilograms consumed.
Thin-wall tools, long flow paths, fast film lines with limited screw length, and parts where the black is only there to hide the resin all point this way.
Its own TDS also allows extrusion up to 5.0%, which WM30 caps at 4.0%.
WM30 is the better fit where the part has to read as black on a thin section, where your specification asks for dispersion finer than Level 3.0, or where the melt needs to stay stiff enough for pipe and sheet.
It is also the one to take if the resin is ABS and modified compounding is on the list.
What WM101 gives you
This is the most free-flowing black grade we publish, 10–20 g/10 min. It melts into the stream quickly on a short screw and fills thin cavities at lower pressure.
We separate the pigment before it is compounded. Carbon black arrives as agglomerates, and agglomerates are what put specks in a black surface.
We wet and separate the pigment first, then fix it on the PE carrier, so the dispersion work is done before the pellets reach your screen pack. Held to Level 3.0 or better.
One bag can cover two departments. Buyers running a molder and a bag line normally hold two black grades, then argue about the shade when a job moves between them.
WM101 is specified for injection and blown film at the dosages above, so one SKU covers both.
Our garbage bag and shopping bag grades sit next to it if you need a tighter fit for one of those two processes.
Pellets are held to one size. Length and diameter are controlled to a single standard instead of drifting with the cutter.
Even feeding is what keeps the carbon black level steady down a long run, and uneven pellets are the most common cause of a shade that shifts halfway through a shift.
If you meter volumetrically, the pelletizing process behind that is worth reading.
Technical Parameter
| Carbon Content | 18%±2 |
| Carrier | PE |
| MFI | 10-20 (g/ 10min(190℃ 10kg) |
| Moisture | ≤0.3% |
| Dispersion | Excellent (≤ Level 3.0) |
| Compliance | RoHS |
| Application | Injection, Pipe (Sewer), Blow film (seafood/garbage bag) |
| Dosage Advice | Injection : 0.8-3.0%, Film blowing: 4.0–8.0% Extrusion: 1.0–5.0% |
| OEM | Accpeted |
Getting consistent results on the line
● Dry the resin. Pellets travel in a sealed bag; resin does not. Two hours at 70–90 °C is the usual figure for PE, and a thin film line notices moisture long before an injection press does.
Bubble breaks, pinholes and silver streaks all point at water that reached the die. If a drying step is not available to you, WM8E is held to ≤ 0.1% moisture and runs straight from the bag.
● Meter by weight. At 4% dosage a 0.2% feed error is a 5% shift in color. Gravimetric feeders hold it; volumetric feeders drift as bulk density changes between batches.
● Tumble blend for ten to fifteen minutes at low speed. A short blend is the most common reason a batch runs differently from the one before it.
● Match the temperature profile to the resin.
The carrier is PE, so a PE line runs unchanged. On a PP job the carrier needs 210 °C and above before it mixes properly, and copying a PE profile across is how streaks start.
● Use the screen pack as a gauge. A 40–80 mesh pack gives you a dispersion reading within minutes. If pressure climbs faster than it did on the previous lot, check the resin before you blame the masterbatch.
● Purge with virgin resin, and plan the sequence. Black is a one-way color. A short charge clears most of it, but nothing replaces running dark before light.
Compliance and documentation
WM101 is declared RoHS, and a certificate of analysis with batch traceability accompanies every shipment. TDS and SDS are available before you order.
Across the range we work to RoHS, REACH, PAHs, FDA and BPA requirements, and we will confirm the position of a named regulation for your market on request.
The regulations and compliance notes cover how those tests are applied.
One thing to settle early. This is not a food-contact grade. Market bags and produce bags get reused to carry food more often than buyers expect, and importers test for it.
Say so at enquiry stage if the film or the part touches food and we will quote from the food-grade range instead.
Frequently asked questions
How much WM101 do I need?
Dosage = target carbon black in the finished part ÷ 0.18. For a part that must carry 0.6% carbon black, that is 0.6 ÷ 0.18, so 3.3%.
Start there, run a short trial, and move in steps of 0.5% until the color matches.
Does 18% carbon black give a deep black?
It depends on dosage and wall thickness. At 4% in a 20 micron bag the film carries about 0.7% carbon black, which reads as charcoal.
If the finished item has to be solidly opaque, or the film must survive outdoors, WM30 or WM8E reaches that level with less material in the hopper.
Can I run it in PP as well as PE?
Yes, in both. The carrier is PE, so on a PP line give the screw enough mixing length, take the melt above 210 °C, and check the surface on the first few meters.
Can it be used with recycled resin?
Yes, and black is the one color that hides the variation reclaimed material brings with it. Start one or two points above your virgin dosage and climb until the color holds.
Heavy recycled content usually means working at the top of the film range.
Will it change the mechanical properties of my part?
The effect is small at these dosages. The carrier is PE with the pigment already dispersed in it, so tensile strength and elongation of the base resin are largely retained.
Confirm on your own formulation, as with any color change.
What ships with the order, and can I get a sample?
A certificate of analysis per batch, the TDS and the SDS. Trial samples are free. Send your resin, the part or the film gauge, and the carbon black level you are working to, and we will confirm grade and dosage within 24 hours.
Packing and Storage
25kg/bag, PE or Composite Paper bag
Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.
Note
The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.
![]() |
Introduction
WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power.
Where WM101 goes
Injection-molded parts that need a black surface
Crates, bins, buckets, pipe fittings, caps, plant pots, cable reels, machine covers, internal structural parts.
On walls of 3 mm and up a working black arrives at a low carbon black level, which is what an 18% grade is for.
The published floor is 0.8%, and on a thin section that reads as charcoal. Most molders settle between 1.5% and 3.0%, and stop once the part matches the reference sample.
Flow matters as much as loading here. At 10–20 g/10 min the melt fills a long, narrow flow path before the front stalls,
so thin-wall and multi-cavity tools run at a lower injection pressure than they would on a stiffer black grade.
Commodity blown film bags
The grade runs at 4.0–8.0% on market bags, T-shirt bags, produce bags, refuse sacks, bin liners and general packaging film. What you get depends on the gauge.
At 4% in a 20 micron bag the film carries about 0.7% carbon black, a soft charcoal where the resin still shows through.
A sack that has to be fully opaque usually wants 1.5–2.0% in the film, which pushes this grade to 8–11%.
You can go there, but past 8% a higher-loaded grade is normally the cheaper route to the same film, so it is worth checking the comparison below first.
Carbon black is also the UV screen in black film. Sheeting that spends its service life in the sun, mulch film, construction covers, waste bags stored outdoors, wants 2% and up in the film.
WM101 reaches that only at the very top of its range. Tell us the end use and we will point you at the outdoor grades instead.
Sheet, profile and conduit
Extrusion runs at 1.0–5.0%. Flat sheet, conduit, corrugated profile and cable duct sit near the top of that band when the surface is visible, and lower when the wall is thick and hidden.
For buried non-pressure drainage and sewer pipe, the general low carbon grade carries a worked cost comparison you can reuse.
WM101 or WM30, which one fits
Both grades run on a PE carrier at the general-purpose end of the range, so buyers often ask which to stock. The two are close enough that the numbers side by side do most of the work.
|
Item |
WM101 |
WM30 |
|
Carbon black content |
18% ± 2 |
32% ± 1.5 |
|
Carrier |
PE |
PE |
|
MFI, 190 °C / 10 kg |
10–20 g/10 min |
1–10 g/10 min |
|
Moisture |
≤ 0.3% |
≤ 0.3% |
|
Dispersion |
≤ Level 3.0 |
≤ Level 2.5 |
|
Compliance |
RoHS |
RoHS |
|
Injection dosage |
0.8–3.0% |
0.8–2.0% |
|
Blown film dosage |
4.0–8.0% |
4.0–8.0% |
|
Extrusion dosage |
1.0–5.0% |
1.0–4.0% |
|
Resins named on the TDS |
PE, PP |
PE, PP, ABS |
More carbon black per bag means less masterbatch per tonne. What each grade needs to reach the same finished color.
|
Carbon black target in the finished part |
WM101 dosage |
WM101 per tonne of resin |
WM30 dosage |
WM30 per tonne of resin |
|
0.5% |
2.8% |
28 kg |
1.6% |
16 kg |
|
1.0% |
5.6% |
56 kg |
3.1% |
31 kg |
|
2.0% |
11.1% |
111 kg |
6.3% |
63 kg |
At a 1.0% target, WM30 gets you there on 31 kg per tonne while WM101 needs 56 kg. Multiply that gap by your annual tonnage and the decision stops being about the price printed on the bag.
Take WM101 when flow and price per kilogram matter more than kilograms consumed.
Thin-wall tools, long flow paths, fast film lines with limited screw length, and parts where the black is only there to hide the resin all point this way.
Its own TDS also allows extrusion up to 5.0%, which WM30 caps at 4.0%.
WM30 is the better fit where the part has to read as black on a thin section, where your specification asks for dispersion finer than Level 3.0, or where the melt needs to stay stiff enough for pipe and sheet.
It is also the one to take if the resin is ABS and modified compounding is on the list.
What WM101 gives you
This is the most free-flowing black grade we publish, 10–20 g/10 min. It melts into the stream quickly on a short screw and fills thin cavities at lower pressure.
We separate the pigment before it is compounded. Carbon black arrives as agglomerates, and agglomerates are what put specks in a black surface.
We wet and separate the pigment first, then fix it on the PE carrier, so the dispersion work is done before the pellets reach your screen pack. Held to Level 3.0 or better.
One bag can cover two departments. Buyers running a molder and a bag line normally hold two black grades, then argue about the shade when a job moves between them.
WM101 is specified for injection and blown film at the dosages above, so one SKU covers both.
Our garbage bag and shopping bag grades sit next to it if you need a tighter fit for one of those two processes.
Pellets are held to one size. Length and diameter are controlled to a single standard instead of drifting with the cutter.
Even feeding is what keeps the carbon black level steady down a long run, and uneven pellets are the most common cause of a shade that shifts halfway through a shift.
If you meter volumetrically, the pelletizing process behind that is worth reading.
Technical Parameter
| Carbon Content | 18%±2 |
| Carrier | PE |
| MFI | 10-20 (g/ 10min(190℃ 10kg) |
| Moisture | ≤0.3% |
| Dispersion | Excellent (≤ Level 3.0) |
| Compliance | RoHS |
| Application | Injection, Pipe (Sewer), Blow film (seafood/garbage bag) |
| Dosage Advice | Injection : 0.8-3.0%, Film blowing: 4.0–8.0% Extrusion: 1.0–5.0% |
| OEM | Accpeted |
Getting consistent results on the line
● Dry the resin. Pellets travel in a sealed bag; resin does not. Two hours at 70–90 °C is the usual figure for PE, and a thin film line notices moisture long before an injection press does.
Bubble breaks, pinholes and silver streaks all point at water that reached the die. If a drying step is not available to you, WM8E is held to ≤ 0.1% moisture and runs straight from the bag.
● Meter by weight. At 4% dosage a 0.2% feed error is a 5% shift in color. Gravimetric feeders hold it; volumetric feeders drift as bulk density changes between batches.
● Tumble blend for ten to fifteen minutes at low speed. A short blend is the most common reason a batch runs differently from the one before it.
● Match the temperature profile to the resin.
The carrier is PE, so a PE line runs unchanged. On a PP job the carrier needs 210 °C and above before it mixes properly, and copying a PE profile across is how streaks start.
● Use the screen pack as a gauge. A 40–80 mesh pack gives you a dispersion reading within minutes. If pressure climbs faster than it did on the previous lot, check the resin before you blame the masterbatch.
● Purge with virgin resin, and plan the sequence. Black is a one-way color. A short charge clears most of it, but nothing replaces running dark before light.
Compliance and documentation
WM101 is declared RoHS, and a certificate of analysis with batch traceability accompanies every shipment. TDS and SDS are available before you order.
Across the range we work to RoHS, REACH, PAHs, FDA and BPA requirements, and we will confirm the position of a named regulation for your market on request.
The regulations and compliance notes cover how those tests are applied.
One thing to settle early. This is not a food-contact grade. Market bags and produce bags get reused to carry food more often than buyers expect, and importers test for it.
Say so at enquiry stage if the film or the part touches food and we will quote from the food-grade range instead.
Frequently asked questions
How much WM101 do I need?
Dosage = target carbon black in the finished part ÷ 0.18. For a part that must carry 0.6% carbon black, that is 0.6 ÷ 0.18, so 3.3%.
Start there, run a short trial, and move in steps of 0.5% until the color matches.
Does 18% carbon black give a deep black?
It depends on dosage and wall thickness. At 4% in a 20 micron bag the film carries about 0.7% carbon black, which reads as charcoal.
If the finished item has to be solidly opaque, or the film must survive outdoors, WM30 or WM8E reaches that level with less material in the hopper.
Can I run it in PP as well as PE?
Yes, in both. The carrier is PE, so on a PP line give the screw enough mixing length, take the melt above 210 °C, and check the surface on the first few meters.
Can it be used with recycled resin?
Yes, and black is the one color that hides the variation reclaimed material brings with it. Start one or two points above your virgin dosage and climb until the color holds.
Heavy recycled content usually means working at the top of the film range.
Will it change the mechanical properties of my part?
The effect is small at these dosages. The carrier is PE with the pigment already dispersed in it, so tensile strength and elongation of the base resin are largely retained.
Confirm on your own formulation, as with any color change.
What ships with the order, and can I get a sample?
A certificate of analysis per batch, the TDS and the SDS. Trial samples are free. Send your resin, the part or the film gauge, and the carbon black level you are working to, and we will confirm grade and dosage within 24 hours.
Packing and Storage
25kg/bag, PE or Composite Paper bag
Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.
Note
The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.


Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

Introduction WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, goo...

Introduction WM8E is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and injection applications. Suitable for PP and PE...

Introduction WM2ADM is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and fiber applications. Suitable for PP and PE m...

Introduction Mulch film is judged in the field, not in the warehouse. By the time a roll reaches the bed former, three things have already decided how the film will behave for the rest of the season: how much carbon black is genuinely in the film, ...

Introduction WMB34 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE ABS PA+GF...

Introduction WM913 is produced by pre-dispersed carbon black with polymer additive, then compounded through plastication. It is widely used in modified compounding applications. Suitable for PP PE ABS PPR ABS HIPS materials. It features low dosage...

Introduction WMEG11 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materi...

Introduction WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in inje...

Introduction WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materia...

Introduction WM16H is produced by pre-dispered carbon black, and then compounded with basic resin. It is widely used in ABS, PC/AS high glossy injection and modifiled compounding applications. Suitable for PP PE PC/ABS GPPS POM GPPS PA+GF materials....

Introduction WM2A is produced by high-pigment carbon black with AS as carrier and special dispersion agent. Its carbon black is stable and blue-shape grade. Suitable for ABS PC high glossy injection materials, also PPO PPS PA PET etc. thermoplasti...

Introduction WM626 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and injection applications. Suitable for HIPS materials. It features lo...

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...