![]() |
![]() |
Introduction
WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.
Automotive interior parts, injection molded
Dashboards and instrument panel components, door trim panels, center consoles, A/B/C pillar trim, glove boxes, HVAC duct sections, seat frame covers.
Most of these parts are molded black and never painted, so an undispersed carbon black speck or a streak lands right on the A-surface. A grained tool makes it easier to spot, not harder.
Modified plastics and compounding
PP filled with talc or calcium carbonate (PP-T20, PP-T30), impact-modified grades built on EPDM or POE, glass fiber reinforced PP, recycled PP going back through a pelletizer.
It also works as the black component in masterbatch let-down blends.
The same grade colors appliance housings, power tool shells, electrical enclosures and general industrial injection parts.
Technical Parameter
| Carbon Content | 17%±1.5 |
| Carrier | PE |
| MFI | 1-10(g/ 10min(230℃ 5 kg) |
| Moisture | ≤0.3% |
| Dispersion | Excellent (≤ Level 2.5) |
| Compliance | RoHS,REACH, FDA, TSCA |
| Application | Injection , Modified compounding |
| Dosage Advice | Injection: 0.8–2.0% Compounding : 1.0–4.0% |
| OEM | Accpeted |
Pellet size holds across the lot. Strand and cutter run in sync, so pellet size stays tight from the first bag to the last. That is what keeps a volumetric feeder honest.
Open a bag carrying a mix of fines and long pellets and the dose starts to drift.
Dispersion survives the mold. Pre-dispersing the carbon black before it meets the carrier keeps agglomerates out of the melt.
Filter pressure rise stays low on compounding lines, and molded parts come out clean. Microscopic dispersion reads level 2.5 or better.
Black at a low loading. At 17% carbon content and high tinting strength, 1.0–1.5% is usually enough for a saturated black in injection.
Staying low also protects the resin properties you paid for. Impact strength and elongation fall as pigment loading climbs.
Stable through heat and repeat passes. Normal PP melt temperatures (200–240 °C) do not shift the shade, and the black holds through drying and re-heat cycles in compounding.
Batch to batch the shade stays close. That matters when you are matching a reference panel six months later.
When the spec goes further. If your part falls under OEM emission limits (VDA 270, VDA 277, VDA 278, GB/T 27630) or needs outdoor weathering, say so at inquiry.
We keep low-VOC interior grades and UV-stabilized grades alongside WM785D and will match the dose to the requirement.
Dry the resin, not the masterbatch. WM785D ships at ≤ 0.3% moisture in a moisture-barrier bag. The PP it goes into usually needs drying more than the masterbatch does.
Dose by weight. A small dosing error shows on a large flat panel long before it shows on a small part. Calibrate volumetric feeders against pellet bulk density, or move to gravimetric dosing.
Tumble blend for 5–10 minutes. A drum mixer is enough. Dropping masterbatch in at the hopper throat and expecting a uniform part generally does not work.
Stay inside the normal PP melt window. Running hotter to chase gloss costs cycle time and gains no blackness.
Purge between grades and colors. Carbon black left in the screw shows up as streaks long after the switch.
On compounding lines, run a 60 mesh screen pack or finer. It tracks dispersion in real time. A flat pressure curve means the pigment is behaving.
WM785D meets RoHS and REACH requirements and is covered by FDA and TSCA statements. PAHs and ELV documentation are available on request.
Tell us which restricted substance list your customer works to and we will confirm against it before shipment. Every lot ships with a COA. Your contact can send the TDS and SDS.
What dosage do I need for a black injection molded PP part?
Start at 1.0%. Most interior parts land between 0.8% and 1.5%. Large flat panels, thin walls or a very deep black target may need up to 2.0%.
Can WM785D go into filled or impact-modified PP compounds?
Yes. Talc-filled, calcium carbonate-filled and EPDM or POE toughened systems all take it. Add it in the same let-down step, at 1.0–4.0% depending on filler loading and the color target.
Will it change the mechanical properties of the finished part?
Adding pigment always has some effect. At 1–2%, impact strength and elongation move only slightly. Keep the dosage as low as your color target allows.
Does it run in PE as well as PP?
It does. Trial it on your own resin, since PE processes at a lower melt temperature.
What documents come with the order?
A COA for each batch, plus the TDS, SDS and compliance statements for RoHS, REACH, FDA and TSCA. Ask for the PAHs or ELV documents if your customer requires them.
Can I get a sample for line testing?
Yes. Send your color target, resin grade and part wall thickness and we will confirm the dosage and ship a trial quantity.
Packing and Storage
25kg/bag, PE or Composite Paper bag
Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.
Note
The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.
![]() |
Introduction
WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.
Automotive interior parts, injection molded
Dashboards and instrument panel components, door trim panels, center consoles, A/B/C pillar trim, glove boxes, HVAC duct sections, seat frame covers.
Most of these parts are molded black and never painted, so an undispersed carbon black speck or a streak lands right on the A-surface. A grained tool makes it easier to spot, not harder.
Modified plastics and compounding
PP filled with talc or calcium carbonate (PP-T20, PP-T30), impact-modified grades built on EPDM or POE, glass fiber reinforced PP, recycled PP going back through a pelletizer.
It also works as the black component in masterbatch let-down blends.
The same grade colors appliance housings, power tool shells, electrical enclosures and general industrial injection parts.
Technical Parameter
| Carbon Content | 17%±1.5 |
| Carrier | PE |
| MFI | 1-10(g/ 10min(230℃ 5 kg) |
| Moisture | ≤0.3% |
| Dispersion | Excellent (≤ Level 2.5) |
| Compliance | RoHS,REACH, FDA, TSCA |
| Application | Injection , Modified compounding |
| Dosage Advice | Injection: 0.8–2.0% Compounding : 1.0–4.0% |
| OEM | Accpeted |
Pellet size holds across the lot. Strand and cutter run in sync, so pellet size stays tight from the first bag to the last. That is what keeps a volumetric feeder honest.
Open a bag carrying a mix of fines and long pellets and the dose starts to drift.
Dispersion survives the mold. Pre-dispersing the carbon black before it meets the carrier keeps agglomerates out of the melt.
Filter pressure rise stays low on compounding lines, and molded parts come out clean. Microscopic dispersion reads level 2.5 or better.
Black at a low loading. At 17% carbon content and high tinting strength, 1.0–1.5% is usually enough for a saturated black in injection.
Staying low also protects the resin properties you paid for. Impact strength and elongation fall as pigment loading climbs.
Stable through heat and repeat passes. Normal PP melt temperatures (200–240 °C) do not shift the shade, and the black holds through drying and re-heat cycles in compounding.
Batch to batch the shade stays close. That matters when you are matching a reference panel six months later.
When the spec goes further. If your part falls under OEM emission limits (VDA 270, VDA 277, VDA 278, GB/T 27630) or needs outdoor weathering, say so at inquiry.
We keep low-VOC interior grades and UV-stabilized grades alongside WM785D and will match the dose to the requirement.
Dry the resin, not the masterbatch. WM785D ships at ≤ 0.3% moisture in a moisture-barrier bag. The PP it goes into usually needs drying more than the masterbatch does.
Dose by weight. A small dosing error shows on a large flat panel long before it shows on a small part. Calibrate volumetric feeders against pellet bulk density, or move to gravimetric dosing.
Tumble blend for 5–10 minutes. A drum mixer is enough. Dropping masterbatch in at the hopper throat and expecting a uniform part generally does not work.
Stay inside the normal PP melt window. Running hotter to chase gloss costs cycle time and gains no blackness.
Purge between grades and colors. Carbon black left in the screw shows up as streaks long after the switch.
On compounding lines, run a 60 mesh screen pack or finer. It tracks dispersion in real time. A flat pressure curve means the pigment is behaving.
WM785D meets RoHS and REACH requirements and is covered by FDA and TSCA statements. PAHs and ELV documentation are available on request.
Tell us which restricted substance list your customer works to and we will confirm against it before shipment. Every lot ships with a COA. Your contact can send the TDS and SDS.
What dosage do I need for a black injection molded PP part?
Start at 1.0%. Most interior parts land between 0.8% and 1.5%. Large flat panels, thin walls or a very deep black target may need up to 2.0%.
Can WM785D go into filled or impact-modified PP compounds?
Yes. Talc-filled, calcium carbonate-filled and EPDM or POE toughened systems all take it. Add it in the same let-down step, at 1.0–4.0% depending on filler loading and the color target.
Will it change the mechanical properties of the finished part?
Adding pigment always has some effect. At 1–2%, impact strength and elongation move only slightly. Keep the dosage as low as your color target allows.
Does it run in PE as well as PP?
It does. Trial it on your own resin, since PE processes at a lower melt temperature.
What documents come with the order?
A COA for each batch, plus the TDS, SDS and compliance statements for RoHS, REACH, FDA and TSCA. Ask for the PAHs or ELV documents if your customer requires them.
Can I get a sample for line testing?
Yes. Send your color target, resin grade and part wall thickness and we will confirm the dosage and ship a trial quantity.
Packing and Storage
25kg/bag, PE or Composite Paper bag
Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.
Note
The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.


Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

Introduction WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, goo...

Introduction WM8E is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and injection applications. Suitable for PP and PE...

Introduction WM2ADM is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and fiber applications. Suitable for PP and PE m...

Introduction Mulch film is judged in the field, not in the warehouse. By the time a roll reaches the bed former, three things have already decided how the film will behave for the rest of the season: how much carbon black is genuinely in the film, ...

Introduction WMB34 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE ABS PA+GF...

Introduction WM913 is produced by pre-dispersed carbon black with polymer additive, then compounded through plastication. It is widely used in modified compounding applications. Suitable for PP PE ABS PPR ABS HIPS materials. It features low dosage...

Introduction WMEG11 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materi...

Introduction WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in inje...

Introduction WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materia...

Introduction WM16H is produced by pre-dispered carbon black, and then compounded with basic resin. It is widely used in ABS, PC/AS high glossy injection and modifiled compounding applications. Suitable for PP PE PC/ABS GPPS POM GPPS PA+GF materials....

Introduction WM2A is produced by high-pigment carbon black with AS as carrier and special dispersion agent. Its carbon black is stable and blue-shape grade. Suitable for ABS PC high glossy injection materials, also PPO PPS PA PET etc. thermoplasti...

Introduction WM626 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and injection applications. Suitable for HIPS materials. It features lo...

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...